RUGGED & REINFORCED, BUILT FOR HIGH-TORQUE COASTAL CRUISING.
The Reefit Tasman 140 is built to handle the higher structural loads generated by dedicated 30 to 40-foot coastal cruising yachts. Engineered specifically around an 8mm forestay wire and 14mm clevis pin standard, this unit features heavily reinforced structural internals to manage high sail torque during heavy-weather reefing. It eliminates the complex, failure-prone tensioning setups of other brands, delivering smooth, frictionless control under load.
Technical Specifications
Typical Boat Length: 10.0m – 12.0m (32.8ft – 39.3ft)
Forestay Wire Size Compatibility: 8mm (5/16”)
Clevis Pin Diameter: 14mm (9/16” imperial equivalent)
Typical Sail Area: 35 – 60 m² (376 – 645 ft²)
Foil Profile: Twin-groove structural alloy (allows twin running sails)
Luff Tape Compatibility: No. 6 luff tape (standard cruising sail finish)
Bearing System: Dual-race open Torlon® ball bearings (zero grease required)
Materials & Construction: Marine-grade anodised aluminium, 316 stainless steel, fully isolated dissimilar metals
Warranty / Service Life:10-Year Comprehensive Warranty / 20+ Year Expected Service Life
What’s In The Box
Every Reefit Tasman 140 kit is shipped as a comprehensive, ready-to-assemble marine system:
Lower Drum Unit: High-capacity drum with open-race Torlon bearing assembly for instant salt flushing.
Halyard Swivel: High-load, smooth-rotating overhead slider block designed to prevent halyard wrap.
Interlocking Foil Extrusions: Robust 2-metre aluminium twin-groove segments, pre-machined for seamless structural alignment.
Internal Joiners & Fasteners: Structural internal sleeves and a complete set of marine-grade stainless fasteners.
Sail Feeder & Top Cap: Integrated entry guides for smooth, snag-free sail hoisting and top torque protection.
DIY Installation Manual: Step-by-step illustrated guide written in plain, practical language.
What You Will Need to Supply: Your existing or new forestay wire, a standard 8mm or 10mm low-stretch furling line, and deck lead blocks to route the line back to your cockpit.
⚠️ Important Sizing Note: If your chainplate pin matches the 14mm profile but your forestay wire size differs from 8mm, please email us directly at sails@reefitsystems.com.au before purchasing so we can custom-verify your setup.
Shipping & Installation
Free Shipping: We include delivery to most Australian locations at no extra charge.
DIY-Friendly Design: Shipped in manageable, cost-effective 2-metre bundles. Perfect for handy boat owners to assemble on the hard or directly at the marina berth without requiring specialised rigging swaging presses.
Foil Kit Ordering Rule: You must select a foil kit to match your rig. Measure your forestay length pin-to-pin and round up to the next available 2-metre increment.
Available Foil Kit Options: 10m | 12m | 14m | 16m | 18m | 20m
The Reefit Relaunch
Our First Production Batch Is Underway.
Following the devastating fire earlier this year, we are officially back on the tools.
This is our very first production run since restarting.
Demand is exceptionally high, and stock is limited.
Configure your specifications below to secure your system.
RUGGED & REINFORCED, BUILT FOR HIGH-TORQUE COASTAL CRUISING.
The Reefit Tasman 140 is built to handle the higher structural loads generated by dedicated 30 to 40-foot coastal cruising yachts. Engineered specifically around an 8mm forestay wire and 14mm clevis pin standard, this unit features heavily reinforced structural internals to manage high sail torque during heavy-weather reefing. It eliminates the complex, failure-prone tensioning setups of other brands, delivering smooth, frictionless control under load.
Technical Specifications
Typical Boat Length: 10.0m – 12.0m (32.8ft – 39.3ft)
Forestay Wire Size Compatibility: 8mm (5/16”)
Clevis Pin Diameter: 14mm (9/16” imperial equivalent)
Typical Sail Area: 35 – 60 m² (376 – 645 ft²)
Foil Profile: Twin-groove structural alloy (allows twin running sails)
Luff Tape Compatibility: No. 6 luff tape (standard cruising sail finish)
Bearing System: Dual-race open Torlon® ball bearings (zero grease required)
Materials & Construction: Marine-grade anodised aluminium, 316 stainless steel, fully isolated dissimilar metals
Warranty / Service Life:10-Year Comprehensive Warranty / 20+ Year Expected Service Life
What’s In The Box
Every Reefit Tasman 140 kit is shipped as a comprehensive, ready-to-assemble marine system:
Lower Drum Unit: High-capacity drum with open-race Torlon bearing assembly for instant salt flushing.
Halyard Swivel: High-load, smooth-rotating overhead slider block designed to prevent halyard wrap.
Interlocking Foil Extrusions: Robust 2-metre aluminium twin-groove segments, pre-machined for seamless structural alignment.
Internal Joiners & Fasteners: Structural internal sleeves and a complete set of marine-grade stainless fasteners.
Sail Feeder & Top Cap: Integrated entry guides for smooth, snag-free sail hoisting and top torque protection.
DIY Installation Manual: Step-by-step illustrated guide written in plain, practical language.
What You Will Need to Supply: Your existing or new forestay wire, a standard 8mm or 10mm low-stretch furling line, and deck lead blocks to route the line back to your cockpit.
⚠️ Important Sizing Note: If your chainplate pin matches the 14mm profile but your forestay wire size differs from 8mm, please email us directly at sails@reefitsystems.com.au before purchasing so we can custom-verify your setup.
Shipping & Installation
Free Shipping: We include delivery to most Australian locations at no extra charge.
DIY-Friendly Design: Shipped in manageable, cost-effective 2-metre bundles. Perfect for handy boat owners to assemble on the hard or directly at the marina berth without requiring specialised rigging swaging presses.
Foil Kit Ordering Rule: You must select a foil kit to match your rig. Measure your forestay length pin-to-pin and round up to the next available 2-metre increment.
Available Foil Kit Options: 10m | 12m | 14m | 16m | 18m | 20m
The Reefit Relaunch
Our First Production Batch Is Underway.
Following the devastating fire earlier this year, we are officially back on the tools.
This is our very first production run since restarting.
Demand is exceptionally high, and stock is limited.
Configure your specifications below to secure your system.
Image 1 of 10
Image 2 of 10
Image 3 of 10
Image 4 of 10
Image 5 of 10
Image 6 of 10
Image 7 of 10
Image 8 of 10
Image 9 of 10
Image 10 of 10
